1-888-9-WEBPETS
(1-888-993-2738)
Certified Seal
Dogs Cats Fish Birds Reptiles Small Pets Pond
Neptune Systems I/O Break Out Box for Apex, Apex Lite, AquaController 3, or AquaController 3 Pro
Click to Image Zoom

Neptune Systems I/O Break Out Box for Apex, Apex Lite, AquaController 3, or AquaController 3 Pro

Out of stock: Email us for an up-to-the-minute inventory update

Add to Wishlist

Quick Overview

Easily add float switches, water on the floor sensors, etc. to the Apex, Apex Lite, AquaController 3, or AquaController 3 Pro. Simply plug the Breakout box`s minidin 8 cable into the AquaController I/O port, and then attach the fl...

Items Similar to Neptune Systems I/O Break Out Box for Apex, Apex Lite, AquaController 3, or AquaController 3 Pro

Product Description
Reviews

Neptune Systems I/O Break Out Box for Apex, Apex Lite, AquaController 3, or AquaController 3 Pro Information



Easily add float switches, water on the floor sensors, etc. to the Apex, Apex Lite, AquaController 3, or AquaController 3 Pro. Simply plug the Breakout box`s minidin 8 cable into the AquaController I/O port, and then attach the float switch, or water on the float switch wires to the quick connector terminals. No soldering or special tools required.
  • 5` Cable plugs into the I/O Connector of the controller.
  • Supports 2 Digital inputs on the AC3.
  • Supports 4 Digital inputs on the AC3Pro.
  • Supports 6 Digital inputs on the PX 1000, Apex, and Apex Lite.
  • Quick Connect Terminals - no soldering required. Recommended for use with 18 to 24 gauge stranded wire.
  • 2 Mounting Holes for easy installation.

Specifications

What's in the Box

Warranty

Articles

Forum Discussion

Expert Reviews

Blogs

+ Display More
- Display Less

Neptune Systems I/O Break Out Box for Apex, Apex Lite, AquaController 3, or AquaController 3 Pro Reviews

"Good" - Product Review by John Zillmer (Posted on 4/3/12)
Rating
Excellent!

Comments: Seems well built, and works fine so far. Wire clamps seem to hold firmly, and are not as difficult to use as I had heard (the little calibration screwdriver that comes with pH meters and refractometers is the right size for the screws on the BOB). Seems like $40 is a bit much for such a simple device, but if it works well I suppose it is worth it.

Do you find this review helpful?  Yes No
"I/O For APEX" - Product Review by German Gaytan (Posted on 12/19/10)
Rating
Excellent!

Comments: Easy to use. In the newer version you screw on the wires, and not clip them on like the picture above. Did not come with instructions, there in the APEX Manual. When plugged to the APEX, you will not see the switches, just use SwitchX in your code: Ex. If Switch(1-6) OPEN/CLOSED Then ON/OFF

Do you find this review helpful?  Yes No
"It works" - Product Review by Kris Stefanski (Posted on 12/4/10)
Rating
Great!

Comments: Easy and simple to hook up, works as advertised. My only 2 issues;
<br />1 - The ground for the switch connections should have a bigger hole. There are 6 connections which all share the same ground, have fun trying to get all six into 1 hole for the ground!
<br />
<br />2 - The cord which connects to the apex should be bigger. Not much options to remotely locate it if you want to have the breakout box closer to your switches.

Do you find this review helpful?  Yes No
"Break out box" - Product Review by David Pomerantz (Posted on 11/29/07)
Rating
Great!

Comments: Very simple hook-up. The wire clips are a little flimsy for someone with large hands.

0 of 3 people found this review helpful, did you? Yes No
"Easy to setup and use" - Product Review by Dwight Keenan (Posted on 10/21/07)
Rating
Excellent!

Comments: I had the I/O box for about three weeks before I got the nerve to remove the float switches I had in place and were working. It took all of about 4 minutes and it was done. Super easy and works well with my Aqua Controller III.Only downside is the instructions are in the manual for the Aqua Controller and don't come with the switch.

10 of 10 people found this review helpful, did you? Yes No